The Power Commander is a fuel injection and ignition timing (on some models) adjustment unit that plugs "inline" with the bikes' stock ECU. The Power Commander uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes, some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the Power Commander's onboard microprocessor. Using this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes' ECU (electronic control unit). Removing the Power Commander returns the bike to its previous stock condition. The Power Commander can be ordered preprogrammed with a your choice of several settings, based on the modifications to your bike. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.

This is for V7 models with twin throttle bodies, it is not compatible with single throttle body models

 This part is available by special order, request a quote

Red NGK spark plug resistor cap with rubbers

Also known as suppressor cap

 Sorry, this part is no longer available.

LD05F

Black NGK spark plug resistor cap with rubbers

Also known as suppressor cap

 More than 5 in stock

LD05F

Black spark plug cap for the standard BPR6ES sized spark plug

Also known as suppressor cap for 12mm spark plugs

 2 in stock

 03717450 GU03717450 03 71 74 50
 0371 7450 0371.7450 03.71.74.50

Spark plug cap for single throttle body models

Also known as suppressor cap Guzzi ref 2D000005 and 2D000247

 2 in stock

 02717450 GU02717450 02 71 74 50
 0271 7450 0271.7450 02.71.74.50

Spark plug cap

Also known as suppressor cap Guzzi ref 2D000005 and GU02717450. See ELA02450 for less expensive alternative

 This part is available by special order, request a quote

2D000247

Marelli phase sensor for Digiplex ignition and tacho

2 pin block connector

 This part is available by special order, request a quote

 20721610 GU20721610 20 72 16 10
 2072 1610 2072.1610 20.72.16.10

Timing sensor for ignition and tacho

3 pin block connector. Used on models with the smaller 15M ECU

 2 in stock

 01721600 GU01721600 01 72 16 00
 0172 1600 0172.1600 01.72.16.00

Oil pressure sender

Can also be used in place of oil pressure switch 17768750 and adapter 19055800 on Monza (check which type your small twin uses before replacing). Replaces two part sensor 31999581.

See ENA12640 for replacement crush washer if required

 4 in stock

19768720-z 19768720 GU19768720 19 76 87 20
 1976 8720 1976.8720 19.76.87.20

Oil pressure sender

See SIA10900 for replacement crush washer if required. Also known as Guzzi and Piaggio refs. 32768710, AP0956169, AP8550512, 486051, 58076R, 826161, 641541, AP9150414. Requires thread adapter ELA88123 to fit to 4 valves per cylinder big twins

 2 in stock

 32768710 GU32768710 32 76 87 10
 3276 8710 3276.8710 32.76.87.10

Also fits Aprilia 1000 RSV4 RF , BJ 2017 -, Aprilia 1000 RSV4 RR , BJ 2016 - 2016, Aprilia 1000 RSV4 RR , BJ 2017 -, Aprilia 1000 Tuono , BJ 2003 - 2003, Aprilia 1000 Tuono Fighter , BJ 2002 - 2005, Aprilia 1100 Tuono V4 RF , BJ 2017 - 2019, Aprilia 1100 Tuono V4 RR , BJ 2016 - 2017, Aprilia 1100 V4 Tuono Factory , BJ 2017 -, Aprilia 125 RS4 , BJ 2017 -, Aprilia 125 RS4 Replica , BJ 2017 - 2018, Aprilia 125 Tuono , BJ 2017 -, Aprilia 900 Dorsoduro , BJ 2017 -, Aprilia 900 Shiver , BJ 2017 -, Aprilia Atlantic 500-,